If a screw turns but doesn’t tighten, the screw hole is stripped. Here’s a quick remedy: Remove the screw and hardware. Dip toothpicks in glue, jam as many as you can into the hole and break them off. You don’t have to wait for the glue to dry or drill new screw holes; just go ahead and reinstall the hardware by driving screws right into the toothpicks.

When you book a handyman through the Handy platform, they'll arrive with a wealth of experience and expertise. From home repair tasks to odd jobs and general labor, a professional handyman will have the know-how and the can-do to get your place looking brand new. In addition to bringing their experience, a Handy handyman will bring all the tools required to get the job done. All you need to do is tell us your address and a few details about the job into the booking request form, and we’ll connect you with an experienced handyman who’s done plenty of jobs like yours. 

If you can see light creeping beneath exterior doors, air is also escaping. Grab a few packages of self-adhesive rubber foam weatherstripping and go to town, sealing any and all doors that lead outside. Weatherstripping already installed but you’re still suffering from a high gas bill? It might be time to replace the strips installed by the previous owners. Check out this handy tutorial on installing weatherstripping.
How to DIY it: A simple cleaning often solves the problem. Start by pulling out the lower dish rack. 
Remove the spray arm and use a thin piece of wire to clean out the holes where water sprays through. Scoop or vacuum out any leftover food 
particles from the filter area, then 
remove the filter screen (above), if possible, and give it a good rinse.
How to DIY it: Coils are located 
on the back of the refrigerator or across the bottom. Pull the fridge away from the wall. (Hint: Grab the sides and pull from the bottom. You may want to lay cardboard on the floor first to prevent scratching.) Clean coils with a coil-cleaning brush (about $10 at home centers), then vacuum. Do this every six months or so.
Risk: If your house was built 
before 1994 and still has the original plumbing fixtures, you’re using 
30 to 40 percent more water than 
a comparable new home. Because about 70 percent of the water flowing through the showerhead is hot, 
that means higher heating bills too. A basic showerhead can cost just $15 and could pay for itself in reduced water and heating costs after just one month. Calculate your 
savings at epa.gov/watersense/watersense-calculator.
Two-part filler has to be mixed and it doesn’t rinse off with water, so it’s not as user friendly as other fillers. However, it’s much tougher and a much better choice for any hole bigger than a nail head, especially outdoors. And it’s not just for wood?you can patch metal, fiberglass?even concrete. Here’s another option for wood filler. Buy some wood filler on Amazon now.

Our Repair Programs focus on a variety of tasks that keep the homeowner safe in their own home.   When possible, volunteer labor is offered at no cost to homeowners. Materials and services are paid for by the homeowner through a not-for-profit loan agreement. The scope of work is defined by SCHFH and agreed on by both parties before the work begins. 
This is a fun one. Composite wood paneling may have been all the rage in the 60s and 70s, but unless it’s still in perfect condition and painted white, it’s probably an eyesore. Popping off this decorative paneling can take minutes, and is seriously satisfying. Just be ready: you never know what condition the wall is in underneath. Be prepared to do a little plaster repair and, of course, repaint. Click here to learn how to prepare a wall for painting.

How to DIY it: This job can be messy, so protect nearby surfaces by covering them with plastic or cardboard. Spray the springs with garage door lubricant (about 
$7 at home centers). Don’t use oil, grease, or other lubricants. They may be cheaper, or you may have them on hand already, but they won’t work as well and tend to pick up dust and grit—just what you don’t want on moving parts.
Almost nothing is quicker, easier or refreshes a room more than a new coat of paint. Even switching up a bright white for a trendy, bright grey can change your whole perspective and give you a starting point for new colors and decoration. Gallons of paint range from $30-$50, and with primer/paint combinations, you will likely only need a gallon or less to finish an average sized room. Add another $10, and you’ll be set with rollers, paint brushes, and painter’s tape. This DIY repair could potentially save you thousands over the cost of a professional painter. Short on time? Click here to learn how to paint a room fast.

Our Repair Programs focus on a variety of tasks that keep the homeowner safe in their own home.   When possible, volunteer labor is offered at no cost to homeowners. Materials and services are paid for by the homeowner through a not-for-profit loan agreement. The scope of work is defined by SCHFH and agreed on by both parties before the work begins. 


How to DIY it: Turn it off by opening the disconnect box (typically located on the outside wall near the unit) and pulling out the disconnect block inside (above). Now take a good look at the unit. If the vents are caked with fuzz from dandelions or cottonwood trees, vacuum the vents. Then rinse the unit with a hose using moderate pressure (the flimsy fins might bend under strong pressure). As you spray, peer down into the unit. You should see water streaming through. If not, the fins are still clogged, so keep rinsing.
Some Service Professionals are employees, franchisees, dealers, or independent contractors ("Corporate SP's") of larger national or corporate accounts ("Corporate Accounts"). In such event, you may be matched with the Corporate Account entity or with one of their Corporate SP's. The above screening criteria is not applicable to Corporate Accounts, and therefore, HomeAdvisor does not screen the Corporate Accounts or Corporate SP's.
Hello my name is Leo and about 22 years ago I entered the world of construction. Throughout the years I have learned many skills and I have used my skills to help people accomplish their projects. I am a father of 4 and family time is very important to me. My family and I started our own community garden where we teach other children how to grow their own garden.
Don’t fall for a shingle shakedown! Not all local handyman services have your best interests in mind.  Instead of repairing damaged roofing or siding, they recommend a full replacement, which doesn’t always make financial sense. At Brothers Services, we believe in treating people fairly and making sure you know your options, including affordable ways to extend the life of your roofing and siding.
Another related issue for avoiding costly repairs (or disasters) is the proper operation of a home, including systems and appliances, in a way that prevents damage or prolongs their usefulness. For example, at higher latitudes, even a clean rain gutter can suddenly build up an ice dam in winter, forcing melt water into unprotected roofing, resulting in leaks or even flooding inside walls or rooms. This can be prevented by installing moisture barrier beneath the roofing tiles. A wary home-owner should be alert to the conditions that can result in larger problems and take remedial action before damage or injury occurs. It may be easier to tack down a bit of worn carpet than repair a large patch damaged by prolonged misuse. Another example is to seek out the source of unusual noises or smells when mechanical, electrical or plumbing systems are operating—sometimes they indicate incipient problems. One should avoid overloading or otherwise misusing systems, and a recurring overload may indicate time for an upgrade.
All jobs are guaranteed and down to the customers satisfaction. Our services e.g ELECTRICAL , PLUMBING , CARPENTRY , DOORS ELECTRIC FENCE , GATE MOTORS TILING , WATERPROOFING , PAINTING WELDING HANDYMAN SERVICES E.G: Hanging of pictures, mirrors, white board or pin board, Signage, paintings, wall papers • Hanging of curtains/blinds • Flat pack furniture assembly • Patio ,sliding door instal ...
If you are willing to buy and pick up the materials yourself, you avoid paying for shopping and pick-up time. But you may find it inconvenient, strenuous, and time-consuming to pick up a load of bricks, a few large sheets of plywood, or similar items. If the company will be doing the shopping and buying, get the company to commit to the time and cost for that task; some will agree that there will be no extra charge.
This summer, they decided to paint the frames black, which cost $900. Mr. Sievers, a special-education teacher, and his wife, a doctor, could have done the work themselves, a solution that do-it-yourself enthusiasts would suggest. But the doors face the street, and the couple wanted the end result to look polished. “My dad and my uncle used to always do home repairs and everything used to come out uneven or crooked,” Mr. Sievers said. So he paid a professional.
If you can’t see any telltale flow marks, and since the stain is fairly small, look at the underside of the roof for ‘shiners.’ A shiner is a nail that missed the framing member, in this case when the carpenter nailed the roof sheathing to the rafters. Moisture that escapes into the cold attic from the rooms below often condenses on cold nails. Sometimes you can spot this if you climb up into your attic on a cold night. The nails will look white because they’re frosted. When the attic heats up a bit during the day, the frost melts and drips, then the nails frost up at night again and so on. The solution is to simply clip the nail with a side-cutting pliers.
Upholstery shops charge almost $200 to fix tears in your seats. You can do it yourself in a few hours with a vinyl and leather repair kit (less than $20) from any auto parts store. You’ll have to practice a bit to get the right color mix and it might not be a perfect match when you’re done, but it’s a heck of a lot better than driving around with torn seats. Start by gluing reinforcing fabric onto the underside of the torn vinyl or leather. Then mix the heat-set filler to match your fabric color and apply it to the tear. Next, find a textured mat that most closely resembles the texture of your vinyl or leather and place it onto the liquid filler. Heat the patching tool with a clothes iron and press it onto the textured mat. Remove the patching tool, but leave the textured mat in place until the patch cools. Then peel it off. Get the full story on repairing leather here.
×