While you’re at it: Any appliance that uses water has a shutoff valve. But when valves go untouched for years, mineral deposits can make them impossible to close. Before that happens, locate the valves for your washer, ice maker, water heater, etc., and turn the handle (clockwise, about a quarter turn) every year or so (more often if your water is very hard), and then turn it back. Here are some ten-minute maintenance tasks you didn’t know you needed.
If you are willing to buy and pick up the materials yourself, you avoid paying for shopping and pick-up time. But you may find it inconvenient, strenuous, and time-consuming to pick up a load of bricks, a few large sheets of plywood, or similar items. If the company will be doing the shopping and buying, get the company to commit to the time and cost for that task; some will agree that there will be no extra charge.

Drip, drip, drip..Having plumbing problems? Or, maybe you need some plumbing help. From repairing kitchen faucets to toilet repair and from plumbing tools to everything including the kitchen sink, Repair-Home makes do it yourself plumbing easy. (And if those blocked drains are driving you plumb crazy, stop hyperventilating. We can find you a plumber for the job.) See All Plumbing
Intimidated by this seemingly daunting project? Don’t be. If you have the will and a whole day (or two) to yourself, you can refinish the hardwood floors in the major areas of your home. You don’t necessarily need to sand, but if the floor is damaged enough to warrant buffing, check out your local hardware store and rent the equipment for anywhere from 4-48 hours. Here’s how to refinish your hardwood floors.
Do you have icicles forming on your nose while you're inside? Perhaps you need home heating and air conditioning help. Learn all about different heating systems including radiant heating, baseboard heating and more. (But when there's so much hot air in your house, you could fry an egg on the floor, please let us help you find a repair guy.) See All Heating & Cooling
You're also less likely to be overcharged if your hire a handyman. Unlike a general contractor or specialist who is more likely to price a job based on the estimated amount of time it will take to complete, you only have to pay a handyman for the hours he works, unless you agree on a flat rate. Handymen can keep their rates low because they don't have to pay additional workers, so they have lower overhead costs than contractors or large companies.
How to DIY it: Clean up any rough edges around the hole, then stick the patch onto the wall over the hole (left). Using the taping knife, spread a layer of joint compound over it and let it dry overnight. Then spread a wider second coat, feathering out the compound on all sides to make the patch blend in. Let it dry, then apply one more coat extending 8 to 12 inches beyond the patch in 
all directions. After the final coat dries, sand the area with a sanding sponge (a foam block wrapped in sand­paper) until it feels smooth and even. Prime, and then paint.
To illustrate, we divided the handyperson services listed on the table below into three groups, based on their charges for four hours of work. The lowest priced one-third of the companies would charge $239 on average for four hours of work, and they were “recommended” by 96 percent of their customers whom we surveyed (see our ratings tables for handyperson services for ratings). In contrast, the highest priced one-third would charge $445 on average for four hours of work and were “recommended” by only 59 percent of their surveyed customers. Just the opposite of what many consumers would assume.
For quality, affordable and reliable service provider for all your handyman needs call Kelvin fast and reliable –From Basic home maintenance such as repairs, carpentry and leak repair to specialized services such as plumbing solutions, waterproofing and electrical work and building projects .PLUMBING - Can will take care of your kitchen and bathroom installations, blockages and water leaks quickl ...
If you can’t see any telltale flow marks, and since the stain is fairly small, look at the underside of the roof for ‘shiners.’ A shiner is a nail that missed the framing member, in this case when the carpenter nailed the roof sheathing to the rafters. Moisture that escapes into the cold attic from the rooms below often condenses on cold nails. Sometimes you can spot this if you climb up into your attic on a cold night. The nails will look white because they’re frosted. When the attic heats up a bit during the day, the frost melts and drips, then the nails frost up at night again and so on. The solution is to simply clip the nail with a side-cutting pliers.
If you are willing to buy and pick up the materials yourself, you avoid paying for shopping and pick-up time. But you may find it inconvenient, strenuous, and time-consuming to pick up a load of bricks, a few large sheets of plywood, or similar items. If the company will be doing the shopping and buying, get the company to commit to the time and cost for that task; some will agree that there will be no extra charge.

Ms. Artale in Westchester has a plan to fix the problem. Neither she nor her husband, Andy, 41, a program analyst, may ever learn how to repair a fence. But that won’t be the case with their 9-year-old son, Matteo. “When my son gets a little older, I’m going to apprentice him out to someone — for real,” she said. “It’s ridiculous that my husband and I don’t know how to do anything.”
This master bath had a few likeable options. Heated tile floors, done by Gabriel tile, Moen U connect faucet that runs via your phone app, double vanity, extra outlet on the right side, humidity sensing fan to eliminate mold and mildew build up. Paint by Father & Son Painting, electrical was LED and done by Heimlich Electric. All plumbing fixtures were Moen, toilet by Kohler.
Every remodeling job starts off with home building plans including detailed floor plans. Next comes the demolition (and a great opportunity to vent off some steam). We can offer you advice on all home renovation jobs big and small, from building modular homes to log homes and from home theater design to closet design. See All Building & Home Improvement

It is not uncommon for power switches and breakers to be accidentally turned off when other appliances are being installed. Homeowners are encouraged to check their circuit breaker to make sure the issue isn’t as simple as needing to turn a switch back on. A circuit breaker is typically located in the garage, although in some homes, the circuit breaker can be found in the basement, hallway or storage room.
Protecting you and your home is our No.1 priority. Every member of our team takes the company credo to heart; treating each customer like family and every home - like our own. It’s not easy trusting a stranger with your most cherished investment. Our skilled and experienced repairmen will earn your trust by listening carefully to your needs and delivering stunning results. We are so confident in our home repair services, we back our work with an ironclad guarantee.
How to DIY it: Take off the loose bar by removing the screws on each of the posts that mount the bar to the wall. (If one side is solidly attached, leave it alone.) With the mounting plate now exposed, try tightening 
the screws in it. If that doesn’t work, remove it. Chances are you’ll find two plastic anchors underneath. Poke them with 
a screwdriver and let them fall inside the wall. Replace with bigger, stronger metal toggle 
anchors (above), sold at hardware stores. Just drive them into the existing holes with a drill 
or a screwdriver, and then re­attach everything.
Upholstery shops charge almost $200 to fix tears in your seats. You can do it yourself in a few hours with a vinyl and leather repair kit (less than $20) from any auto parts store. You’ll have to practice a bit to get the right color mix and it might not be a perfect match when you’re done, but it’s a heck of a lot better than driving around with torn seats. Start by gluing reinforcing fabric onto the underside of the torn vinyl or leather. Then mix the heat-set filler to match your fabric color and apply it to the tear. Next, find a textured mat that most closely resembles the texture of your vinyl or leather and place it onto the liquid filler. Heat the patching tool with a clothes iron and press it onto the textured mat. Remove the patching tool, but leave the textured mat in place until the patch cools. Then peel it off. Get the full story on repairing leather here.
×