A garbage disposal is a bit scary when it’s turned on and the blades are noisily chopping up kitchen waste. But, if your disposal gets stinky, fear not. It’s easy to clean out the gunk and get rid of the smell. If the splash guard needs replacing, you can do that in 20 minutes! If you need to replace the entire disposal you can replace it yourself.
Simple fixes for the four most common refrigerator problems: an ice-maker breakdown, water leaking onto the floor, a cooling failure and too much noise. Chances are, you can solve the problem yourself, save some money and avoid the expense and inconvenience of a service appointment. The following article will walk you through the simplest solutions to the most common fridge malfunctions. Learn how to repair a refrigerator here.

How to DIY it: Gently tug the loose part of the carpet to find the point where it’s still attached. Snip 
it off as close to the backing as possible and save it. Use painter’s tape to surround the repair area. Squeeze 
a heavy bead of carpet seam sealer (about $6 at home centers) into the run. Then fill in the hole with the saved fiber, using a screwdriver to press it into the sealer bit by bit until the area looks like the surrounding 
carpet (below).
If a screw turns but doesn’t tighten, the screw hole is stripped. Here’s a quick remedy: Remove the screw and hardware. Dip toothpicks in glue, jam as many as you can into the hole and break them off. You don’t have to wait for the glue to dry or drill new screw holes; just go ahead and reinstall the hardware by driving screws right into the toothpicks.
When that happens, all you can do is pay up, as happened with Jason Hark and Kenneth Larivee. In 2016, the couple got hit with a $28,000 assessment to replace the siding on their West Orange, N.J. townhouse in a condo association. This cost came on top of their $610 monthly association fee. After speaking with siding companies, Mr. Hark estimated that if his unit had been a stand-alone property, the project would have cost closer to $7,500. “But we couldn’t fight it,” said Mr. Hark, a director at WCBS-TV.
A handyman is not the best option for a large or complicated project that could take a long time to complete and requires the help of multiple workers. You shouldn't turn to a handyman either if you need an emergency service for plumbing, electrical or appliance work, unless the handyman is licensed in that trade. If an unlicensed person does plumbing or electrical work, you have no guarantee that the work has been done to code, which could affect your homeowners insurance policy or any claim related to the work. Use a contractor or specialist for remodeling work, room additions and projects that require heavy-duty equipment or licensed professionals like electricians.
Plumbing vent boots can be all plastic, plastic and metal, or even two-piece metal units. Check plastic bases for cracks and metal bases for broken seams. Then examine the rubber boot surrounding the pipe. That can be rotted away or torn, allowing water to work its way into the house along the pipe. With any of these problems, you should buy a new vent boot to replace the old one. But if the nails at the base are missing or pulled free and the boot is in good shape, replace them with the rubber-washered screws used for metal roofing systems. You’ll find them at any home center with the rest of the screws. You’ll have to work neighboring shingles free on both sides. If you don’t have extra shingles, be careful when you remove shingles so they can be reused. Use a flat bar to separate the sealant between the layers. Then you’ll be able to drive the flat bar under the nail heads to pop out the nails.
While you’re at it: Any appliance that uses water has a shutoff valve. But when valves go untouched for years, mineral deposits can make them impossible to close. Before that happens, locate the valves for your washer, ice maker, water heater, etc., and turn the handle (clockwise, about a quarter turn) every year or so (more often if your water is very hard), and then turn it back. Here are some ten-minute maintenance tasks you didn’t know you needed.
How to DIY it: You should already be emptying the lint trap before every load of laundry. To do a thorough cleaning of the dryer and its vent duct system, unplug the machine (and turn off the gas valve if it has one). Pry off the access panel on the front (try a putty knife covered with duct tape to prevent scratching) and vacuum around the motor and heating element (above). Then carefully disconnect the vent duct tubing from the back of the dryer and use a dryer vent brush (about $10 at home 
centers; look for one that also cleans refrigerator coils) to pull out any 
accumulated lint. Aim to do this at least once a year.
recently, had anything home repairs both redesign & construct a new bathroom in our home. this requi...red our bathroom to be fully gutted for the purpose of the reconstruction. we are overwhelmingly pleased with the results. this bathroom is now a virtual show place in our home. our contractor , scott was extremely knowledgable & carefully as well as caringly assisted us in the purchases of a new floor, vanity, sink, cabinets, toilet, tub, tiling as well as all plumbing fixtures. the quality of the work is frankly, perfect. when the job was completed , the cleanup provided by anything home repairs left our newly renovated bathroom spotless . an all thunbs up recommendation for anything home repairs for those in need of high quality & honest home construction &/or repairs. See More
In theory, the cost of building-wide improvements should be less in a condo because it is spread out across dozens of residents, and the sheer scale of the project could lower the overall price. But it does not always work out that way. Condo board members are volunteers who may not be skilled negotiators or knowledgeable about construction. They may take the first bid they get, or agree to more work than is necessary. If complications increase the cost of the job, residents won’t necessarily know. “This is one of the potential downsides of a condo or co-op scheme,” said Eric D. Sherman, a real estate lawyer and partner in the New York office of Pryor Cashman. “Lots of the time, boards are under the gun. They’re not paid for their efforts, they take the first bid from the first contractor that they see and they say, ‘sign me up.’”
If you are willing to buy and pick up the materials yourself, you avoid paying for shopping and pick-up time. But you may find it inconvenient, strenuous, and time-consuming to pick up a load of bricks, a few large sheets of plywood, or similar items. If the company will be doing the shopping and buying, get the company to commit to the time and cost for that task; some will agree that there will be no extra charge.
Upholstery shops charge almost $200 to fix tears in your seats. You can do it yourself in a few hours with a vinyl and leather repair kit (less than $20) from any auto parts store. You’ll have to practice a bit to get the right color mix and it might not be a perfect match when you’re done, but it’s a heck of a lot better than driving around with torn seats. Start by gluing reinforcing fabric onto the underside of the torn vinyl or leather. Then mix the heat-set filler to match your fabric color and apply it to the tear. Next, find a textured mat that most closely resembles the texture of your vinyl or leather and place it onto the liquid filler. Heat the patching tool with a clothes iron and press it onto the textured mat. Remove the patching tool, but leave the textured mat in place until the patch cools. Then peel it off. Get the full story on repairing leather here.
×