Tiny holes in shingles are sneaky because they can cause rot, a leaky roof and other damage for years before you notice the obvious signs of a leak. You might find holes left over from a satellite dish or antenna mounting brackets or just about anything. And exposed, misplaced roofing repair nails should be pulled and the holes patched. Small holes are simple to fix, but the fix isn’t to inject caulk in the hole. You’ll fix this leaky roof problem with flashing.

Here’s a quick fix for a drawer front that’s pulling off. Cut a couple of lengths of quarter-round the same height as the drawer sides. Hold them in place while you drill a couple of holes through the sides and front of the drawer box. Dab some polyurethane glue (wood glue doesn’t stick well to finished surfaces) on the pieces of quarter-round before screwing them into place. Here’s how to fix sticky wooden drawers.

Here’s a quick fix for a drawer front that’s pulling off. Cut a couple of lengths of quarter-round the same height as the drawer sides. Hold them in place while you drill a couple of holes through the sides and front of the drawer box. Dab some polyurethane glue (wood glue doesn’t stick well to finished surfaces) on the pieces of quarter-round before screwing them into place. Here’s how to fix sticky wooden drawers.
When you hire handyman services, you need to be sure that the team is going to turn up on time. Nothing is more frustrating than being given an 8 hour arrival window, forcing you to take a day off of work to sit around and wait. And nothing is more frustrating than a last minute cancellation.  When you book handyman services through Handy, you can be sure that they'll arrive at the time you request. We’ll connect you with the right people for the job so you can worry about the things that really need your attention—not fixing that light fixture.
Plumbing vent boots can be all plastic, plastic and metal, or even two-piece metal units. Check plastic bases for cracks and metal bases for broken seams. Then examine the rubber boot surrounding the pipe. That can be rotted away or torn, allowing water to work its way into the house along the pipe. With any of these problems, you should buy a new vent boot to replace the old one. But if the nails at the base are missing or pulled free and the boot is in good shape, replace them with the rubber-washered screws used for metal roofing systems. You’ll find them at any home center with the rest of the screws. You’ll have to work neighboring shingles free on both sides. If you don’t have extra shingles, be careful when you remove shingles so they can be reused. Use a flat bar to separate the sealant between the layers. Then you’ll be able to drive the flat bar under the nail heads to pop out the nails.
How to DIY it: A simple cleaning often solves the problem. Start by pulling out the lower dish rack. 
Remove the spray arm and use a thin piece of wire to clean out the holes where water sprays through. Scoop or vacuum out any leftover food 
particles from the filter area, then 
remove the filter screen (above), if possible, and give it a good rinse.
Check for cracked housings on plastic roof vents and broken seams on metal ones. You might be tempted to throw caulk at the problem, but that solution won’t last long. There’s really no fix other than replacing the damaged vents. Also look for pulled or missing nails at the base’s bottom edge. Replace them with rubber-washered screws. In most cases, you can remove nails under the shingles on both sides of the vent to pull it free. There will be nails across the top of the vent too. Usually you can also work those loose without removing shingles. Screw the bottom in place with rubber-washered screws. Squeeze out a bead of caulk beneath the shingles on both sides of the vent to hold the shingles down and to add a water barrier. That’s much easier than renailing the shingles.
Risk: If your house was built 
before 1994 and still has the original plumbing fixtures, you’re using 
30 to 40 percent more water than 
a comparable new home. Because about 70 percent of the water flowing through the showerhead is hot, 
that means higher heating bills too. A basic showerhead can cost just $15 and could pay for itself in reduced water and heating costs after just one month. Calculate your 
savings at epa.gov/watersense/watersense-calculator.
We specialize in turning your honey-do’s into honey-done’s! whether it’s sprucing up your home for the holidays, finishing a construction project, or even managing your seasonal home maintenance list, call us anytime and we’ll help conquer your list! At Brothers, we don’t just provide home repair services, we create lasting relationships with area homeowners and bring trust back into the home improvement process.
Intimidated by this seemingly daunting project? Don’t be. If you have the will and a whole day (or two) to yourself, you can refinish the hardwood floors in the major areas of your home. You don’t necessarily need to sand, but if the floor is damaged enough to warrant buffing, check out your local hardware store and rent the equipment for anywhere from 4-48 hours. Here’s how to refinish your hardwood floors.

A garbage disposal is a bit scary when it’s turned on and the blades are noisily chopping up kitchen waste. But, if your disposal gets stinky, fear not. It’s easy to clean out the gunk and get rid of the smell. If the splash guard needs replacing, you can do that in 20 minutes! If you need to replace the entire disposal you can replace it yourself.
Turn2Us Handyman Services was created with the homeowner in mind. Our goal is to help you with all your household projects by providing a full handyman service or simply providing a handyman to help you with your to-do list. No need to call multiple businesses to handle your projects, we can do it all! We are dedicated to providing you with the best handyman service available at the most affordable price without sacrificing quality.
Everything was simply unforgettable! I responded to an ad for Black Friday Special: name your price for the job with no reasonable offer refused! I emailed the company letting them know I wanted some rotten wood replaced on the window dormer and a ceiling repaired and painted. Mike said he would trust what and wanted and the price of $400.00. The carpenter and the painter arrived early. Mike arrived shortly and went over what needed to be done. I had purchased treated lumber so Mike purchased with receipt the correct wood. The carpenter quickly saw that more rotten wood had to be replaced than anticipated. The carpenter had to do wood cutting to frame and restore the dormer as well as insulate, caulk and prime the untreated wood. Needless to say, the handyman special turned out to be a skillful carpentry job. Mike, nevertheless kept the price at $400.00, which also included the plaster repair for the ceiling as well as painting the entire ceiling. I had been told in the past by two contractors that the ceiling job was complicated. Mike and his painter made the job uncomplicated and the result was simply great!
Risk: If your house was built 
before 1994 and still has the original plumbing fixtures, you’re using 
30 to 40 percent more water than 
a comparable new home. Because about 70 percent of the water flowing through the showerhead is hot, 
that means higher heating bills too. A basic showerhead can cost just $15 and could pay for itself in reduced water and heating costs after just one month. Calculate your 
savings at epa.gov/watersense/watersense-calculator. 
×