If you have shallow scratches or nicks, hide them with a stain-filled touch-up marker. Dab on the stain and wipe off the excess with a rag. But beware: Scratches can absorb lots of stain and turn darker than the surrounding finish. So start with a marker that’s lighter than your cabinet finish and then switch to a darker shade if needed. For deeper scratches, use a filler pencil, which fills and colors the scratch. Or, try using a walnut to remove scratches in wood!

Check for cracked housings on plastic roof vents and broken seams on metal ones. You might be tempted to throw caulk at the problem, but that solution won’t last long. There’s really no fix other than replacing the damaged vents. Also look for pulled or missing nails at the base’s bottom edge. Replace them with rubber-washered screws. In most cases, you can remove nails under the shingles on both sides of the vent to pull it free. There will be nails across the top of the vent too. Usually you can also work those loose without removing shingles. Screw the bottom in place with rubber-washered screws. Squeeze out a bead of caulk beneath the shingles on both sides of the vent to hold the shingles down and to add a water barrier. That’s much easier than renailing the shingles.
Generally, in the United States, there are few legal issues if an unpaid homeowner works on a project within their own home, with some exceptions. Some jurisdictions require paid handymen to be licensed and/or insured. New Jersey, for example, requires all handymen who work in for-profit businesses serving residential and commercial customers, to be registered and insured.[21] Often handymen are barred from major plumbing, electrical wiring, or gas-fitting projects for safety reasons, and authorities sometimes require workers to be licensed in particular trades. However, minor plumbing work such as fixing water taps, connecting sinks, fixing leaks, or installing new washing machines, are usually permitted to be done without licensing. Many handymen are insured under a property damage liability policy, so that accidental property damage from negligence or accidents are covered.
Before you go through the trouble of repainting a ceiling to get rid of a water stain, try this trick. Spray the spot with a bleach and water solution (10 percent bleach), and wait a day or two. If it’s an old stain, use a mold and mildew remover from the grocery store. You’d be surprised how often the stain disappears by the next day. It works on both flat and textured ceilings.
While you’re at it: Don’t cheap out and use rock salt instead of water-­softener salt, even though rock salt costs half as much. It contains far more impurities that will clog up the works, and you could wind up needing to spend $600 or more for a new water softener. Make sure you always follow these home care tips to save you time, money, and stress.
Need some ideas for kitchen remodeling? We all have dreams of a perfect kitchen design. From choosing the right kitchen cabinets to designing practical kitchen islands and appliance repair, we'll help that dream come true. (And if you're tired of eating take out and need some help with the renovations, we'll get you a contractor right away.) See All Kitchen
If you can’t see any telltale flow marks, and since the stain is fairly small, look at the underside of the roof for ‘shiners.’ A shiner is a nail that missed the framing member, in this case when the carpenter nailed the roof sheathing to the rafters. Moisture that escapes into the cold attic from the rooms below often condenses on cold nails. Sometimes you can spot this if you climb up into your attic on a cold night. The nails will look white because they’re frosted. When the attic heats up a bit during the day, the frost melts and drips, then the nails frost up at night again and so on. The solution is to simply clip the nail with a side-cutting pliers.
Upholstery shops charge almost $200 to fix tears in your seats. You can do it yourself in a few hours with a vinyl and leather repair kit (less than $20) from any auto parts store. You’ll have to practice a bit to get the right color mix and it might not be a perfect match when you’re done, but it’s a heck of a lot better than driving around with torn seats. Start by gluing reinforcing fabric onto the underside of the torn vinyl or leather. Then mix the heat-set filler to match your fabric color and apply it to the tear. Next, find a textured mat that most closely resembles the texture of your vinyl or leather and place it onto the liquid filler. Heat the patching tool with a clothes iron and press it onto the textured mat. Remove the patching tool, but leave the textured mat in place until the patch cools. Then peel it off. Get the full story on repairing leather here.
José was quick to respond to my request for an estimate to install a new back door. He came over and sized it up, sent me a fair priced quote the next day, and was back with workers soon after I accepted the quote and immediately started working. I'm extremely satisfied with the work that was performed--and the door needed to be framed and set inside the metal frames for the house, which is a little more complex than a regular door installation. I will definitely hire Jose and Jireh Contractor again!
Sooner or later, every sprayed ceiling is going to get a water stain or a scrape. Spray texture in a can won’t perfectly match every ceiling texture, but it’s usually close, and a lot easier than respraying a whole ceiling. Before spraying, seal the patch with a stain-blocking primer, cover the floor and furniture, and practice your technique on scrap plywood or cardboard. Buy ceiling texture on Amazon now.
This is a fun one. Composite wood paneling may have been all the rage in the 60s and 70s, but unless it’s still in perfect condition and painted white, it’s probably an eyesore. Popping off this decorative paneling can take minutes, and is seriously satisfying. Just be ready: you never know what condition the wall is in underneath. Be prepared to do a little plaster repair and, of course, repaint. Click here to learn how to prepare a wall for painting.
Upholstery shops charge almost $200 to fix tears in your seats. You can do it yourself in a few hours with a vinyl and leather repair kit (less than $20) from any auto parts store. You’ll have to practice a bit to get the right color mix and it might not be a perfect match when you’re done, but it’s a heck of a lot better than driving around with torn seats. Start by gluing reinforcing fabric onto the underside of the torn vinyl or leather. Then mix the heat-set filler to match your fabric color and apply it to the tear. Next, find a textured mat that most closely resembles the texture of your vinyl or leather and place it onto the liquid filler. Heat the patching tool with a clothes iron and press it onto the textured mat. Remove the patching tool, but leave the textured mat in place until the patch cools. Then peel it off. Get the full story on repairing leather here.
Everything was simply unforgettable! I responded to an ad for Black Friday Special: name your price for the job with no reasonable offer refused! I emailed the company letting them know I wanted some rotten wood replaced on the window dormer and a ceiling repaired and painted. Mike said he would trust what and wanted and the price of $400.00. The carpenter and the painter arrived early. Mike arrived shortly and went over what needed to be done. I had purchased treated lumber so Mike purchased with receipt the correct wood. The carpenter quickly saw that more rotten wood had to be replaced than anticipated. The carpenter had to do wood cutting to frame and restore the dormer as well as insulate, caulk and prime the untreated wood. Needless to say, the handyman special turned out to be a skillful carpentry job. Mike, nevertheless kept the price at $400.00, which also included the plaster repair for the ceiling as well as painting the entire ceiling. I had been told in the past by two contractors that the ceiling job was complicated. Mike and his painter made the job uncomplicated and the result was simply great!
Risk: If your house was built 
before 1994 and still has the original plumbing fixtures, you’re using 
30 to 40 percent more water than 
a comparable new home. Because about 70 percent of the water flowing through the showerhead is hot, 
that means higher heating bills too. A basic showerhead can cost just $15 and could pay for itself in reduced water and heating costs after just one month. Calculate your 
savings at epa.gov/watersense/watersense-calculator.
×